Felix Machines - Cell Fabrication Solutions

Precision Stacking Machine FM-NXT150

The FM-NXT150 Precision Stacking Machine (Pat. Pending) is designed for accurate Z type stacking of single or multi-layer pouch cells. The stacker incorporates adjustable electrode guides to easily accommodate a variety of cell sizes. The hold down clamp assembly and separator carriage can be easily removed to fit the stacker through a large glovebox antechamber. Key Features: -Designed for lab scale prototyping of single or multi-layer cells -Capable of accommodating a wide range of electrode sizes -Stacker will fit through most large antechambers with minimal disassembly -No power or compressed air required -High accuracy adjustable guides and stack alignment -Easily maintained separator/anode/cathode offsets -Minimal maintenance needed -100% designed, fabricated and assembled in the United States

Benchtop Vacuum Coater FM-TMH800

The FM-TMH800 is a large table top coating machine designed for a wide variety of substrate coating applications including battery and super capacitor fabrication. The coater's quick setup and flexibility is ideal for research environments, and it's small size means it can be easily relocated and repurposed. The coater is designed with an integrated heater to improve coat drying times, and features a touch screen for simplified operation. Key Features: -Touch screen for simplified operation -Aluminum vacuum chuck designed to easily hold substrate firmly in place -Adjustable coat length up to 1000mm is ideal for R&D -Drying temperature is easily set via the touchscreen -Doctor blade can be easily cleaned and adjusted for different coat widths

Ultrasonic Welding Machine FM-CSH1000

The FM-CSH1000 Ultrasonic Welding Machine is designed for battery research and development in a laboratory setting. It produces very strong welds with low internal resistance, and offers a clean final weld appearance without any traces of oxidation. A variety of weld parameters can be adjusted for improved strength, layer penetration and conductivity in a wide range of materials. Key Features: -Superior weld conductivity with near zero internal resistance -Welding oxidized or contaminated surfaces is not an issue -No flux preparation or pre-treatment needed for parts -Welds in as little as 0.01 seconds -Wear resistant weld head reduces maintenance and down time

3 in 1 Vacuum Sealer FM-RJY200

The FM-RJY200 3 in 1 Vacuum Sealing Machine is used to seal the edges of a pouch cell without vacuum, seal a cell under vacuum, and degas and reseal a pouch cell after electrolyte injection. This model is customizable and can also be utilized for electrolyte diffusion. The RJY200's small size and separate control unit is ideal for use in a glovebox. Key Features: -Top & side edge heat sealing without vacuum -Electrolyte diffusion cycle without sealing -Vacuum/final seal cycle -Independent upper and lower seal bar temperatures -Copper seal bars provide superior heat transfer -View port allows for observation while sealing or diffusion is in progress -Multi-stage adjustable cycles for customized diffusion -Aluminum chamber reduces total weight and provides superior corrosion resistance -Touch screen operation

High Power Ultrasonic Welding Machine FM-CSH2000

The FM-CSH1000 Ultrasonic Welding Machine is designed for battery research and development in a laboratory setting. It produces very strong welds with low internal resistance, and offers a clean final weld appearance without any traces of oxidation. A variety of weld parameters can be adjusted for improved strength, layer penetration and conductivity in a wide range of materials. Key Features: -Superior weld conductivity with near zero internal resistance -Welding oxidized or contaminated surfaces is not an issue -No flux preparation or pre-treatment needed for parts -Welds in as little as 0.2 seconds -Wear resistant weld head reduces maintenance and down time -2000W power enables larger welds through more layers simultaneously

Pouch Emboss Machine FM-CK200

The FM-CK200 Pouch Emboss Machine quickly and reliably fabricates embossed battery cases from flat polymerized foil squares. The precision dies ensure clean and accurate case fabrication without wrinkling or corner collapse. Designed with multiple safety features including dual activation triggers and an IR safety sensor, the CK200 is quick, safe, and reliable. Key Features: -Emboss dies are customizable and easy to replace -Emboss depth is easily adjusted -Produces clean cases with no corner collapse or wrinkling -Dual hand emboss activation ensures safe operation -Features an IR safety sensor to prevent injury -Protective shield is included -Integrated cycle counter keeps track of pouch fabrication

Compact Coater With Heated Cover FM-TMH250

The FM-TMH250 is a compact table top coating machine designed for a wide variety of substrate coating applications including battery and super capacitor fabrication. The coater's low cost and flexibility is ideal for research environments, and it's small size means it can be easily relocated and repurposed. The coater is designed with a heated cover to improve coat drying times, and features a touch screen for simplified operation. Key Features: -Touch screen for simplified operation -Aluminum vacuum chuck designed to hold substrate firmly in place -Built-in vacuum pump removes the need for extra equipment -Adjustable coat length -Temperature of heaters are easily set via the touchscreen -Doctor blade can be replaced or adjusted for different coat widths

Compact Vacuum Coater FM-TM300

The FM-TM300 is a compact table top coating machine designed for a wide variety of substrate coating applications including battery and super capacitor fabrication. The coater's low cost and flexibility is ideal for a research environments, and it's small size means it can be easily relocated and repurposed. The integrated touchscreen allows for quick settings adjustment. Key Features: -Touch screen operation -Aluminum vacuum chuck is designed to hold a variety of substrates -Adjustable coat length -Variable coat speed -Easily adjustable doctor blade gap

Heated Calender Machine FM-JS100

The FM-JS100 is designed for battery electrode calendering, and features heated rollers and a digital display for easy operation. In addition, it offers a wider degree of flexibility than standard calender machines with the optional roll to roll accessory (sold Separately). Key Features: -Digital thermostat display with a maximum temperature of 120°C -Safety covers for heated rollers -Dual height adjustments for highly accurate and level operation -Roller speed can be easily adjusted -Roller rotation can be reversed -Electric motor and controller ensure steady and even pressure -Optional roll to roll addition makes longer electrodes easy to calender

Calender Machine FM-DCM100

The FM-DCM100 is designed for battery electrode calendering. It features dual micrometer readouts, and offers a wider degree of flexibility than standard calender machines with the optional roll to roll addition (sold separately). This model comes in a variety of roller widths up to 250mm. Key Features: -Dual height adjustments for highly accurate and level operation -Adjustable speed with a digital or analog display for improved simplicity -Roller rotation can be reversed for added flexibility -Electric motor and controller ensure steady and even pressure -Optional roll to roll addition makes longer electrodes easy to calender

Manual Calender Machine FM-DSL-100

The FM-DSL Series Manual Calender Machines are designed for battery electrode or other substrate calendering. Dual micrometer readouts allow for accurate gap control, and a manual drive method enables operation in locations without power. This model comes in a variety of roller widths. Key Features: -Dual height adjustments for highly accurate and level operation -Manual speed control eliminates the need for a power supply -Roller rotation can be reversed for added flexibility -Roller material hardness is >HRC62 for improved material compression and lifespan

Hydraulic Calender Machine FM-DYRG330

The FM-DYRG330 is designed for roll to roll battery electrode calendering. It incorporates large 200mm diameter rollers with a hydraulic pressure system for superior compression on materials up to 330mm wide. This calender machine also incorporates automatic alignment and tension control, simple touch screen interface, and an optional heated roller upgrade. Key Features: -Easily adjustable and precise calendering gap -Integrated tension control and alignment for roll to roll use -Automated material supply and take-up rollers offer precise control -Simple touch screen operation -Optional heater can be adjusted from room temperature to 130°C -Can be ordered with or without roll to roll take-up/supply units

Roll to Roll Slitting Machine FM-CFT-R300

The FM-CFT-R300 is a roll to roll slitting machine designed for cutting electrodes for cylindrical or pouch cell batteries from a continuous supply roll. The slitting die incorporates high precision tungsten alloy blades for clean and repeatable slitting operations. Multiple points of adjustment to the system allows the CFT-R300 to slit a wide variety of materials and thicknesses. Key Features: -Ultra-fine tungsten alloy blades provide superior performance and lifespan -Precision blades offer high accuracy cuts with minimal burrs or artifacts -Blade speed is independently adjustable relative to substrate speed -Capable of slitting a variety of materials and thicknesses -Automatic tension control system with multiple points of adjustment -PLC controls for easy and repeatable operation

Roll to Roll Coating Machine FM-SY300

The FM-SY300 Roll to Roll Coating Machine is a three roll transfer coating system which can be used for continuous and intermittent coating. While the FM-SY300 serves a variety of coating applications, its primary function is research or pilot scale battery electrode coating. Featuring precision coat adjustment, and an ultra wide 280mm maximum coat width, it is specially designed to produce repeatable and accurate electrodes every time. A modular design option is also available with multiple dry zones. The modular option features separate slurry application, drying and foil take-up segments which allows for easier shipping, anoatingd enables extended dry zones to specification. Key Features: -Continuous and intermittent coating -Modular design option also available with multiple dry zones -Double or single sided coating -Coater is equipped with tension control and active tension correction -Oven has upper and lower convection heating to maintain even drying -Coating blade with precision adjustment to obtain even and accurate coat thickness -Gap tracking for double sided coating -Automated PLC control system

Vacuum Oven FM-ZKX50

Manual Winding Machine FM-YSJ65

5V6A Battery Tester FM-CT-4008-5V6A-S1

The FM-CT-4008-5V6A-S1 is a three range, 8 channel battery or super-capacitor tester. This equipment can test in the 0.5mA - 0.1A, 0.1A - 3A, and 3A -6A ranges, and provides accurate data for both current and voltage. The independent channel control of the 5V6A tester allows it to be used for a wide range of applications such as materials research, quality control in manufacturing, research & development, and battery cell testing.

Electrode Slitting Machine FM-FT300

The FT300 is a semi-automated slitting machine designed for cylindrical or pouch cell electrodes. The slitting die is 300mm wide, and can be fully customized to any number and size of electrode strips. If your project requires a die wider than 300mm, this machine can be customized to fit your need. Key Features: -Slitting speed is adjustable -Includes a safety cover for the cutting area -Standard die is 300mm wide, custom dies are available -Designed for precise cuts with minimal burr -Compact table top design saves space in your lab

Semi-Automatic Stacking Machine FM-SAS200

The FM-SAS200 Semi-Automatic Stacking Machine is designed to assemble anode, cathode, and separator materials in a Z fold configuration for pouch cell battery fabrication. Utilizing PLC control and automation, the SAS200 is capable of accurately stacking up to 500 layers or 30mm. Manual operation consists primarily of loading materials and adjusting stack settings. Both the electrode placement and separator manipulation is automated, which allows for more efficient and accurate assemblies.

5V50mA Battery Tester FM-CT-4008-5V50mA-164

Show more